About a third of bearing failures are caused by lubrication. The most frustrating part is that a large share of them come not from a lack of lubrication but from the wrong lubrication. Too much grease, the wrong consistency, mixing two incompatible greases: each can finish a bearing as fast as never greasing it at all. In this post we start with what is inside grease and look at what the numbers on the tub mean, and how much to pump in and how often.
What is grease, and how is it different from oil?
Grease is a structure that holds base oil inside itself, the way a sponge holds water. What lubricates is not the grease itself but the base oil inside it. The thickener is only the carrier that keeps that oil inside the bearing, close to the contact zone.
NLGI consistency grade: that number on the tub
The NLGI number on the grease tub states the grease's hardness, that is, its consistency. It has nothing directly to do with lubricating ability; it only tells you how fluid it is.
Base oil viscosity: the real selection criterion
Even with the right NLGI grade, if the base oil viscosity is wrong there is no lubrication. The rule is simple: the higher the speed, the thinner the oil; the heavier the load and the lower the speed, the thicker the oil.
In a fast-running bearing, thick oil increases drag and temperature. In a heavily loaded, slow-turning bearing, thin oil cannot form a film in the contact zone, and metal touches metal.
| Operating condition | Base oil viscosity (40 °C) | Typical place |
|---|---|---|
| High speed, light load | 46–100 cSt | Electric motor, spindle |
| Medium speed, medium load | 100–220 cSt | Fan, pump, gearbox |
| Low speed, heavy load | 220–460 cSt | Crusher, conveyor drum |
| Very slow, shock loads | 460 cSt and above + EP additive | Crane, mining equipment |
Compatibility: mixing two greases
This is the most common and quietest mistake in the field. The brand changes when the grease gun is refilled, nobody notes it, and months later the bearing starts running hot.
The problem is that when two different thickeners mix, the structure can break down. The mixture either thins and runs out of the housing, or hardens and stops releasing oil. Either way, the bearing is left unlubricated.
If you are changing grease brand or type, clean the old grease out of the housing completely. If you cannot clean it, grease several times in a row with the new grease to purge the old, and watch the bearing closely in the following weeks.
How much grease?
At first fill, grease 30–50% of the bearing's free space and at most half of the housing. At high speed stay near the lower limit; at slow speed and heavy load go towards the upper limit.
For relubrication there is a simple formula:
G = 0.005 × D × B
G = grease quantity (grams)
D = bearing outside diameter (mm)
B = bearing width (mm)
Example
Bearing 6309: outside diameter 100 mm, width 25 mm.
G = 0.005 × 100 × 25 = 12.5 grams
A standard grease gun delivers about 1–1.5 grams per stroke, so 8–12 strokes for this bearing. Weighing your grease gun's actual output once takes the guesswork out of every greasing after that.
How often?
Two things set the interval: the speed factor and temperature.
The speed factor is the bearing's mean diameter multiplied by its speed (n × dm). As this value grows, the grease ages faster and the interval shortens. The curves in catalogues are based on this value.
The effect of temperature is striking, and it is often left out of maintenance plans:
| Bearing temperature | Grease life | Interval |
|---|---|---|
| 70 °C | Reference | Catalogue value |
| 85 °C | Halves | Half |
| 100 °C | Drops to a quarter | A quarter |
| 115 °C | Drops to an eighth | An eighth |
The rule is: above 70 °C, grease life halves for every 15 °C rise. If you keep greasing a hot-running bearing at the same interval, the bearing runs dry between greasings, and you only notice when it fails.
The harm of too much grease
Grease is an obstacle. The rolling elements have to keep pushing the grease in front of them to clear a path. When the space is completely full, that work turns into heat.
The typical course of overgreasing is this: the bearing heats up, the warm grease thins and runs, and the running grease seeps out past the seal or reaches the motor winding. As the temperature rises, the base oil evaporates, the hardened thickener is left behind, and the bearing is no longer being lubricated.
- A slight rise in bearing temperature after greasing is normal; it lasts until the excess grease spreads out and should drop within a few hours.
- If the temperature does not drop and keeps rising, too much grease has been pumped in.
- If the housing has a drain plug, keep it open while greasing so the excess can escape.
- On electric motors, excess grease that reaches the winding damages the insulation. Do not neglect the drain when greasing motors.
Grease point hygiene
Even if the grease itself is clean, if you put the gun on without wiping the nipple you push the dust on it straight into the bearing.
- Wipe the nipple and its surroundings with a clean cloth before greasing.
- Wipe the nozzle of the grease gun too; a gun left open on the bench collects dust.
- Use a clean spatula when taking grease from a drum; do not put your hand or a dirty tool in.
- Drums should be kept closed; water collects on top of an open drum and the grease emulsifies.
- Label which grease goes to each lubrication point. A colour-coded label system largely prevents mix-ups.
Quick checklist
- Choose base oil viscosity by speed and load; NLGI alone is not enough.
- If in doubt, start with NLGI 2.
- Find out the thickener type and check its compatibility with the existing grease.
- At first fill, put in grease equal to 30–50% of the bearing's free space.
- For relubrication, use the formula
G = 0.005 × D × B. - Weigh how many grams your gun delivers per stroke, once.
- If the bearing is above 70 °C, halve the interval for every 15 °C.
- Keep the drain plug open while greasing.
- Do not grease without wiping the nipple.
Lubrication is the most frequently done but least thought-about job in maintenance. Pumping the right grease, in the right amount, at the right interval adds no extra cost; it only asks you to sit down and work it out once and then stick to it. In return, your bearings come close to their catalogue life.
Frequently asked questions
Can different greases be mixed?
Greases with incompatible thickeners can soften and run out or harden when mixed. If the grease type changes, purge the old grease as far as possible, check a compatibility chart and grease more often at first.
How much grease does one stroke of a grease gun give?
It varies by gun; a standard gun gives about 1–1.5 grams per stroke. To give the right amount, weigh ten strokes of your own gun and work out grams per stroke.
What harm does over-greasing do?
If the housing fills up, the grease churns, temperature rises, the grease breaks down and seals are stressed. In electric motors excess grease can reach the windings and damage insulation.
Sources
This article is a compilation based on the sources below and personal experience; its assessments are opinions. In practice, the manufacturer's official documentation and applicable regulations take precedence.
- ASTM D217 — Cone Penetration of Lubricating Grease (NLGI class measurement method)
- ISO 3448 — Industrial liquid lubricants: ISO viscosity classification
- SKF — Rolling bearings (lubrication section)
Comment
No comments yet. Be the first to comment!
Leave a comment